These networks are WPA, not WEP.
You need to look at the WPA tutorials, not the WEP ones.
Sorry Guest, you are banned from posting and sending personal messages on this forum.
This ban is not set to expire.
|
11
on: November 12, 2022, 07:27:53 pm
|
||
| Started by zuk726 - Last post by misterx | ||
|
12
on: November 12, 2022, 10:34:04 am
|
||
| Started by zuk726 - Last post by zuk726 | ||
|
Hi, I'm a total noob, could someone please help me to get started? I was trying follow the tutorials Simple WEP Crack and How to crack WEP with no wireless clients, to capture packets for cracking the WEP key of my own wireless home network, from the machine which I normally use. The wireless card is "Intel Corporation Centrino Advanced-N 6205".
Everything seems to work: monitor mode is enabled, injection is reported to be working, fake authentication is reported as successful. Until aireplay-ng then starts capturing, and then captures endlessly without any result. I can understand that no ARP packages are captured (in the 1st tutorial), since my home network probably doesn't send any. But why are not data packets captured (in the 2nd tutorial), even when I am using another machine to surf the web in my home network at the same time? Are all those "read packets" shown in the counter only beacons or something? Code: [Select] me@My-Home-PC:~$ sudo aireplay-ng -3 -b A1:A1:A1:A1:A1:A1 -h HH:HH:HH:HH:HH:HH wlp3s0monCode: [Select] me@My-Home-PC:~$ sudo aireplay-ng -5 -b A1:A1:A1:A1:A1:A1 -h HH:HH:HH:HH:HH:HH wlp3s0I noticed that my home network shows up as 2 endpoint BSSIDs. The first on channel 1, and the second on channel 48. I seem to be using the second when connecting normally, but fake authentication only works against the first. For the second, only failure is reported when attempting fake auth, after 16 tries. Even for the "variation for picky access points". Code: [Select] me@My-Home-PC:~$ nmcli dev wifiDoes someone have an idea why no packets are captured? What would the correct approach be with 2 BSSIDs for the same network? Can I run some analysis to find out what's going on here? Thanks for any help and insights! |
||
|
13
on: November 05, 2022, 08:45:50 pm
|
||
| Started by leste - Last post by Ufo | ||
|
Confirming the above. Although I had to make some adjustments
replace the firmware Code: [Select] sudo mv /lib/firmware/ath10k/QCA6174/hw3.0/firmware-6.bin_bckp"Enable" Code: [Select] sudo modprobe -r ath10k_pciSolve potential rfkill problems Code: [Select] sudo rfkill unblock wifi; sudo rfkill unblock allStop some deamons -> less stuff to kill later Code: [Select] sudo service NetworkManager stopChange the wifi-card into the mon mode Code: [Select] sudo ifconfig wlp4s0 downScanning should work Code: [Select] sudo airodump-ng wlp4s0Running ubuntu 20.04, btw, can't be bothered installing Kali or whatever. |
||
|
14
on: October 19, 2022, 09:02:04 pm
|
||
| Started by raidriar - Last post by misterx | ||
|
Another place you want to look is in the git repository, there is a branch called 'aircrack-ng-cell'. However, I don't remember if there was any commit or anything done in that branch.
A pull request for it is very welcome. Considering how old it is, it may be worth starting from git master (or another version as recent as possible) and port these changes, if necessary in there. However, I don't know how up to date Puppy is. |
||
|
15
on: October 19, 2022, 12:41:25 am
|
||
| Started by raidriar - Last post by raidriar | ||
|
I am looking to try to run aircrack-ng on PPC/CELL BE on a linux distro on PS3. I see an old comment on the github referring to something like this, but where is the source? I would like to compare what was done with the original, and perhaps expand upon the aforementioned patch.
https://github.com/aircrack-ng/aircrack-ng/issues/534 |
||
|
16
on: September 25, 2022, 07:26:37 pm
|
||
| Started by umaric7 - Last post by Snafu | ||
|
I know this is an old thread but in case anyone else is interested, I've had good luck with the AWUS036ACH card running Kali on a Raspberry Pi.
Just make sure you download the drivers via: apt install realtek-rtl88xxau-dkms |
||
|
17
on: September 13, 2022, 06:49:33 am
|
||
| Started by lushanclous - Last post by lushanclous | ||
|
Please help, is it a problem with this chip, do I need to buy another network card
|
||
|
18
on: September 13, 2022, 06:48:14 am
|
||
| Started by lushanclous - Last post by lushanclous | ||
|
I use ASUS AX56 network card to turn on monitor mode, the attack makes the device offline, but can't get the handshake packet, the chip is rtl8852au, I have the driver ready --- from Google Translate
|
||
|
19
General Category / General help / Re: airodump-ng fails to capture 5Ghz 20Mhz,30Mhz channel width channels.
on: September 02, 2022, 07:57:52 pm
|
||
| Started by programmer - Last post by misterx | ||
|
1. 30MHz, not with airodump-ng, and very likely not this device/driver
2. My guess would be to set the regulatory domain to that: "iw reg set XX" |
||
|
20
General Category / General help / airodump-ng fails to capture 5Ghz 20Mhz,30Mhz channel width channels.
on: September 01, 2022, 03:23:49 pm
|
||
| Started by programmer - Last post by programmer | ||
|
Hi every one i have installed parrot os after that i pluged in my alfa usb AWUS036ACH adapter and installed rtl88xxau-mdk i start airmon-ng and also sudo airodump-ng —band a wlan0 its show 5ghz wifi wich have only 40Mhz channel width and its show me only US and Pak country region 5ghz devices like Power beem M5 my question is that :
How can i see 20Mhz or 30Mhz channel channel frequencies How can i see Australia and any country region device i will be very thankful if anyone solve my issue |
||